Thin jaw duck bill pliers. About 7" long. Volkswagen T Trim Removal Wedge. Volkswagen VAG New Beetle Convertible Set of 2 tools. With special hex key screwdriver 14" mm long with 4mm hex bit tip. And special 13mm hollow socket 10" mm long, with a 17mm outside hex. Made in Germany by Stahlwille. Stahlwille number Volkswagen VAS Made by hand from a pair of pliers. Due to the special production and very low quantity of these made, the finish may be rough, with spots and off color.
The tool will work just fine. From Scirocco and up. Rear Window Cable Installation tool for window regulator. Brake Tools. Perfect for VW drum brakes. Brake adjusting tool-for adjusting hand brakes brake cable.
Brake Pedal release tool. Pull Hook for handbrake return spring. Volkswagen TA Brake Pedal release tool. Improved version of tool T This is the most common size, see other sizes listed below.
Note: Customers report that this tool must have 30mm cut out and welded back to work on a Right Hand Drive car, such as found in Australia. If you know of a tool for RHD cars, please let us know.
Other Brake Pedal Release. Brake Piston reset tool to be used in conjunction with T Similar to Kukko and Mercedes tool number 52 43 Assembly Tool that is used for installing protective cap on brake caliper unit.
Set of 6 cups. Volkswagen TB. Ships 3 pounds. Complete with Plate and with triangle shape pins. Two pins, with spacing of outside diameter 36mm, inside diameter 28mm. Pin size 7x4mm. This is the new replacement for the tool. Used to rotate the brake caliper piston back into position to allow room for the installation of new pads.
Note: This tool will not work on the new electronic parking brake with 3 pin caliper. If your car has the electronic parking brake you need a diagnostic system to perform this service. Please visit Ross-Tech. Porsche Cayenne. VV Touareg.
Overall Also used for camshaft gear bolt on Touareg V Rear Axle Brake Caliper bolts. Same as Mercedes tool number 01 09 Go to Mercedes Page. Brake Push Rod Release Tool. For Audi Q5 from and up. Used to release the brake servo push rod. Stahlwille 54X-M Stahlwille Rear Brake Caliper Socket. See Stahlwille Click Here. Stahlwille Brake Adjustment Lever.
Brake pedal actuator. This will keep the brake pedal pushed down during maintenance work on the brake system. The "L" bracket is placed against the driver seat, then push the round button on top and the "V" bracket can be pushed against the brake pedal. Release the round button and the brake pedal is locked in position. Note: This tool is for maintenance and repair work only, any other use is prohibited.
Do not depend on this device to stop a car, or keep it from rolling away. If you are outside the 48 States, extra shipping charges will apply. Please email us before purchasing this item. Camshaft Tools. Klann camshaft clamp tool for timing belt changing. Use on Audi V6 with 2 valve engine.
Ship 6 pounds. We will ship the best way. If you need faster shipping please call or email us with your address. Only one available at sale price. Matador 00 Matador Camshaft Locking Set. Similar to the Volkswagen tool Volkswagen A. Diesel Camshaft Timing Tool. Setting Bar, camshaft lock used to hold camshaft when setting diesel timing. VW factory tool A.
Used on and older diesel cars. Oil seal extractor camshaft oil seal. Also some crankshaft. This the current replacement for old tool number and Extractor Picture 2 Bolt Picture 2. Camshaft Seal Bolt used in conjunction with to remove camshaft seal. For Audi A4 and up, with 4-cylinder engine.
Retainer for fuel injection pump gear, or Eurovan camshaft drive sprocket. With 10mm pins and about mm 15" long. Camshaft Timing Locating flange, set of 2. Audi V8 Engine 3. No Longer Available!! Crank Oil Seal Extractor. Used to remove left and right front camshaft oil seals. V6 engine. Camshaft holder, Hold the camshaft on V6, 2 valve engine when installing belt. See KL German tool for a better price! Click here. Camshaft Ruler. Camshaft locating fixture, set of 2 plates.
Audi A8. Engine V8 3. Camshaft Locking Bar V6, 5-valve engine. Audi A4 A6 year and up. The bar is mm 27" long overall. There are 2 pins on each side, a 6mm and 8mm. The distance between the pins is 54mm on center. The big holes are 40mm diameter. Chrome plated steel. Similar to Factory tool Includes both wedges and Pin. Needed to loosen tension on the timing chains during the camshaft and phaser service procedure.
Used on the VW Routan and Chrysler 3. This tool is the replacement for old tool VW A Camshaft Locks. Used to lock the camshaft when servicing the Oil Control Valves on Routan with 3. The is for Right Bank, the is for Left Bank. Lock for Twin Camshaft Sprockets 4 Cylinder 1. Counter holder for removing and installing camshaft sprocket on 4 Cylinder 1.
With 3 pins , spacing 41mm. Overall length mm 16". Camshaft bar. This special tool TA supersedes camshaft bar T Camshaft bar that is used for locking camshaft without having to remove cylinder head cover.
Used on 4 Cyl. Camshaft Clamp, Polo and up. No Longer Available! See next tool TB. Special Order! Camshaft Clamp. For 4 cylinder direct injection 2. Tooth Belt Pulley Puller. For removal of toothed belt pulley found on 6-cyl.
TDI common rail engines 3. Set of 3 Assembly Camshaft Tools. Applicable on: Audi A3 with 4-cylinder gas direct injection, 1. Set of 3 sockets. Volkswagen TC. Applicable on: Audi A3 with 4-cylinder gas direct injeection, 1.
Same as factory tool T Extractor for the Camshaft Phasing Gears with 5 and 6 spokes. Additional Claw for extractor. For 4 cylinder direct injection engine 2. Please Note: These arms will only fit the number T factory tool!
Twin Camshaft Holder. Use on Audi A6 and A8. Use this tool to align camshaft at top dead center when installing timing belts, tensioners or head assembly. Use with , T, and V8 Engine. Special Socket. For Camshaft Assembly V6 3. Volkswagen TSET. Camshaft Clamp set for Audi A4 and A6 with 3. Set with 5 tools. Sir tools VA cam lock set - similar to T factory tool. T exhaust cam socket. T crank lock pin. T Belt Tension Lock Pins. Please Note: the VA comes in a case, the other tools are supplied loose.
The VA is an aftermarket tool, the other tools are genuine factory tools. Camshaft Locator for Audi S4 Sedan. Adjustment pins used to secure the camshaft when adjusting valve timing on TDI common rail 6 cyl and 8 cly engines. Set of 2 pins. Volkswagen T Camshaft Correction Tool. FSI Special Order. Camshaft Adjustment Socket. Needed to tension the timing chain on Audi A6 and up 8-cyl. Length 50mm. This is the VW Polydrive type socket. Locating Pins. For Camshaft Assembly 8 cylinder 4. Set of Spacers for location of camshaft sliding piece.
Please NOTE : The service literature is not clear, but in some cases you may need 2 sets to get enough of the size needed for the engine you are doing.
Please check to see how many of each size you will need. You may need to buy 2 sets. For sliding pieces on the camshaft found in Audi A4 from and up, Audi Q5 from and up.
Volkswagen T Camshaft Lock. Camshaft Socket used to rotate and hold the camshaft on 1. Camshaft Wrench for timing chain work on VW 4. Set of 2 Camshaft Clamps. Used to lock camshaft sprocket at TDC on the 4 Cylinder 1. Clutch Tools.
Hazet Valve Shim Pliers. VW-Audi 1. Also for releasing master cylinder push rod from clutch pedal. This is the 12 point "triple square". High Quality and made in the European Union. Esgen SXZ Drift for pressing in taper roller bearing outer race on the clutch housing. Volkswagen VWA. Clutch Pedal Bushing Install tool.
Clutch Centering Disc. Assembly of self-adjusting clutch cable. Clutch Centering Mandrel, and crankshaft needle bearing press. With 15mm Pilot Tip and 20mm step. Also needed for Porsche Boxster. Clutch rod release tool. Release master cylinder push rod from clutch pedal.
See Tool T Clutch Release Tool. Used to disconnect the clutch pedal from the master cylinder. Not available at this time. Special Pliers used to separate the clutch pedal from the clutch master cylinder. Flywheel lock for servicing clutch 1. Clutch Alignment Tool. It has a step near the tip. The tip is 21mm and steps up to 22mm. Volkswagen T Clutch pedal over-center spring assembly tool. Used to remove and install over-center spring when bearing bracket is removed.
Guide Sleeve for Clutch Plate. About 85mm long. For 6 Speed Gearbox 02E. Clutch Bearing Gauge. Used to adjust the clutch engagement position of bearings K1 and K2.
Dual Clutch gearbox 0AM from June and up. Supplied in a plastic storage box. Used for centering the clutch plate on manual gearboxes 0B1, 0B2, 0B3 and 0B4. Similar to Volkswagen tool T Sauer And some heat shields.
No Longer Available from Sauer. Now in stock in the Esgen Brand. And other jobs needing application of caulk or sealant. Accepts ml 10oz cartridge.
Special release feature prevents run on. Old Version. No Longer Available!!! New Version. Cooling System. AMF VW Caliper face spanner. For Radiator fan clutch removal, or hydraulic pump pulley. With 5mm Pins. Overall Length mm. Do not force it in the wrong direction and break the pins on the tool! We will not replace the tool! Due to the heat this part is exposed to and possibility of rust, the part could be stuck in place. It is best to soak the nut with liquid wrench before attempting this job.
Gedore 44 5. Same as Volkswagen See Gedore Page. Viscous coupling wrench, 32mm. Plastic dip-handle. Note : This item is to be used only on Viscous Fan Hubs!! About 11" in length. This size is NO Longer Available. Viscous coupling wrench, 36mm. Claw for heater.
No longer available! Hose Clamp set of two. Up to 40mm. Press tool for viscous fan bearing. For use with a torque wrench. Please consult your service manual for the assigned value. Puller for Coolant Pump Gear. Touareg and up, Transporter and up. For 5 cylinder diesel engine.
Water pump puller. Transporter and up. Special 12mm torque wrench insert ring wrench. To remove the pulley bolt on drive sprocket of cooling pump belt. Audi A3 with 4 cylinder gas direct injection. Also use on Porsche Macan. With 9x12mm rectangle mount for use with a German Torque Wrench.
No longer available. Cooling System Pressure Tester, With pressure gauge reading 0 to 4 bar. Flexible hose with quick connect, and adapter for volkswagen style test caps. Adapter used to pressure test the expansion tank. New Beetle, etc.
Diamater 62mm threads. Adapter used to pressure test the cooling system cap. Adapter for cooling system on V6. Crankshaft Tools. Puller needed to remove the clutch pilot bearing from the crankshaft on Dasher. About Remove crankshaft oil seal on flywheel end. Special tip. For Turbo Diesel 1. About mm 12"inch long. Crankshaft seal installing tool flywheel side.
Also used when pressing the large taper roller bearing outer race in bevel box cover. This tool is made with 3 parts.
This set has 2 tools. Volkswagen factory tool It 27mm 12 point. Overall length is mm. FourM Brand 4M Same as old factory tool The is no longer available from VW.
We can now supply the 4M tool from Europe. FourM 4M Counter holder for removing the crankshaft pulley center bolt. The tools is no longer available from VW. We can supply the FourM 4M Lever for removing front cranshaft oil seal. Front Crankshaft Oil Seal. Sauer Crankshaft Vibration Damper holding tool. Discontinued by VW and Sauer.
Crankshaft oil seal fitting sleeve on VR6 engine. We can supply an aftermarket tool. Special Order delivery about 1 week. Crankshaft holder, Hold crankshaft when installing belt or flywheel. See new tool T Crankshaft counter holder that is used to remove and install the vibration damper.
Engine AAN. Pilot Bearing Driver. Used to install needle bearing in crankshaft on some V6 engines. Fitting Sleeves for crankshaft oil seal on vibration damper end. Crankshaft counter holder.
For VR6 engine. Size 46mm. Counter-hold tool for installing vibration damper. Eurovan with VR6 Engine. Crankshaft Counter Holder with pins for toothed belt sprocket. Used when replacing crankshaft oil seal. No Longer Avaliable. See tool T for this job.
Crankshaft Install. To install the crankshaft sprocket and vibration damper on VW Routan. Made in USA. Crankshaft Adapter Audi TT from and up. For 5 Cylinder gas direct injection engine 2. Vibration Damper Counter Hold tool for Eurovan. For T4 Transporter with 2. Extra Long Bar. It could go UPS ground and delay delivery. For same job as factory tool T Special short design. About mm 13" Long.
High quality. Used in place of old tools A and Thrust piece. Used when installing crankshaft oil seal pulley side. Locking pin.
Used to lock crankshaft when serving clutch. Crankshaft Stop. Locking crankshaft at crankshaft sprocket when adjusting timing. For pulley with timing at o'clock timing position. See T for new version found on some engines. Counter hold bar to prevent the crankshaft from rotating during the removal of the crankshaft center bolt. Factory tool made from premium steel in Germany! Minimal effort is needed when using this tool. Used when adjusting timing on engine with oval belt pulley.
For pulley with o'clock timing position. Volkswagen T C. Crankshaft Seal Install tool. Used with dial gauge VAS , not included. Used to check Top Dead Center on engine 1. Also 2. Body mm long, Pin mm. Also used to counter hold the camshaft and oil pump. With 2 extra pin sets. With 10 Pin sets included. Note: the previous kit TN has been upgraded. Crankshaft Locking Pin Golf and up. Volkswagen T Seal Installer Crankshaft.
Audi A3 with gas 4-cylinder direct injection 2. Counter holder for vibration damper. Ships 7 pounds. Diesel Crankshaft Spur Gear Puller. Used on 4-cyl.
Crankshaft Vibration Damper Assembley Set. For 4 Cylinder 1. Installing crankshaft oil seal. Crankshaft oil seal extractor. Assembly tool for renewing PTFE crankshaft seal. Crankshaft key used for turning crankshaft when removing and installing camshaft timing chain. Socket used to turn crankshaft. For Audi A6 and up, Audi A8 and up. Engine 6 cylinder 2. Crankshaft lock 6-cyl 2. Volkswagen T Crankshaft locking pin.
Outside diameter 62mm with 21mm hex drive. Here is Audi special tool number T Audi A6 year and up. Audi A7 Sportback year and up. Aud A8 year and up. Cylinder Head Tools. Just click here. Similar to Volkswagen Hazet Cylinder Head Socket. For Audi V6 engines. Cylinder Head Bolt Socket. Guide Pin set for Cylinder head centering. CSRF token.
Currency change. Customer recognition. Customer-specific caching. Individual prices. PayPal payments. Saves selected country. Saves selected currency. Selected shop. Comfort functions. These cookies are used to make the shopping experience even more appealing, for example for the recognition of the visitor. Affiliate program. Conversion and usertracking via Google Tag Manager. Google Analytics. Track device being used. Description Evaluations 0. Close menu. Reference numbers: VAG , T, T The original comparison numbers are for identification purposes only, they are not original tools.
Evaluations 0. Read, write and discuss reviews Write an evaluation. I have read the Privacy Policy. Matching accessories 25 Customers also bought Customers also viewed. Matching accessories Universal counterholder for camshafts pullys VAG counterholder key for crankshafts like Camshaft fixing tool VAG T original.
VAG Camshaft adjuster removal tool like T, Timing chains change tool for valve timing like Lever for chain tensioner like VAG T Back-up tool for crankshaft pulley as VAG T VR6 Timing chain tool for valve timing like VAG driving sleeve original VW special tool. Universal puller set for camshaft gear as VAG VAG dial gauge with holder for axial play like Holder for dial gauge for axial play like VAG Locking tool for crankshaft and camshaft like Offset screwdriver like VAG T Pegging tool for tension pulley like VAG T T-handle puller for spark plug connector, Customers also bought.
0コメント